Home
> Lutron Dimmers
> Lutron Grafik Eye Lighting Controls
> Lutron GRAFIK Eye 3000 Series Multi-Scene Preset Dimming Controls
> Lutron GRX-3506 Grafik Eye 3000 Series 6-Zone PC Programmable Preset
Dimming Control Unit
- Description: Lutron GRX-3506 Grafik
Eye PC Programmable Incandescent / Magnetic Low Voltage / Neon / Cold-Cathode
/ Tu-Wire Fluorescent 6-Zone Control Unit
Can link up to 8 GRAFIK Eye Control Units (8 addresses) for
up to 48 zones
Up to 16 Accessory Controls for total of 24 control points
Built-in Infrared Receiver/Optional Infrared Wireless
Remote Control
Can increase individual zone capacities to 30,000 W/VA at
120V/277V
Power Interfaces are necessary for Fluorescent (GRX-FDBI)
and Electronic Low Voltage (GRX-ELVI). Power Interfaces are not required with
HP 2-4-6 Dimming Module.
GRX-TVI– Provides a 0-10V output that
conforms to BSI 929. Can be used to switch all lighting loads, including metal
halide and electronic ballasts. If switching other non-lighting loads, use a
relay by others.
| |
|
|
TOTAL WATTS / VA |
| GRAFIK Eye Model No. |
No. of Zones |
Wallbox Size in Gangs* |
120V |
100V (-JA) |
220-240V (-AU) |
230V(-CE) |
|
GRX-3106- GRX-3506- |
6 |
4 |
2000 |
1600 |
3000 |
2300 |
|
Global Product Offerings |
| Volts |
Zone
Capacity |
| 120 V |
6.7 A / 800W / VA |
| 100V |
6.0 A / 600W / VA |
| 220-240V |
5.0A / 1200W / VA |
| 230V |
3.4A / 800W / VA |
* Mount in standard multiple
gang wallbox, 2.75" deep minimum, 3.5" deep recommended.
† (1) No. SB-4G required.
†† CE requires SB-4G (4 gang) wallbox. |
Sources:
Incandescent, magnetic and electronic low-voltage, neon/cold cathode,
fluorescent (with Lutron dimming ballasts), switched loads.
Power Failure Memory: Lights
automatically return to prior levels: scenes and fade times are saved.
Input Power: 50/60 Hz from
conventional utility systems. Consult Lutron if power is from a generator. |
|
GRAFIK Eye 3000 System Wiring
Diagram below illustrates basic system wiring for GRAFIK Eye 3000 Series
Control Units. Note: For wiring multiple Control Units, Interfaces, and
Accessory Controls, system wiring should be: Low Voltage Class 2 (SELV) 4-wire
daisy chain of two No. 18 (1 .0mm 2) twisted pairs (4 wires); two Belden 9740,
or one Liberty LU02PSH18EX-GRN. For complete system wiring information, see 3000
Series Installer’s Guide.
|
Power Booster and Interface Wiring
For GRAFIK Eye 3000 Series controls only, Lutron Power Boosters can be added to
increase zone capacities. Consult factory for other load types (e.g. HID). (For
120V, Power Interfaces are not required with HP 2 - 4 - 6 Dimming Module.)
|
For more information click on the PDf
files below.
|
GRAFIK Eye 3000 Control Units : Preset architectural lighting control
units with integral dimmers for scene-based control of several small
wattage-
120-127 volt -
English |
Grafik Eye
Load Interfaces
Increases single zone load capacity and converts dimming signals for control
of additional load types.
Grafik Eye PB,
power booster -
English
Grafik Eye
ELVI,
electronic low-voltage interface -English
Grafik Eye
FDBI,
fluorescent dimming ballast interface -
English
|
Grafik Eye
Architectural Control
All Architectural models-
English
NTGRX-2B, 2-button with status light-
English
NTGRX-4B, 4-button-
English
NTGRX-4S, 4-scene on off and raise/lower-
English
NTGRX-4S-IR, 4-scene on off and IR-
English
|
|
